10 Misconceptions Your Boss Shares Concerning Timber Sash Windows Cambridge

Door Hinge Repair Cambridge

The hinges on your doors are a small but crucial element that can make a significant difference in the look and performance of your doors. Replacing the hinges that sound squeaky is a quick and inexpensive upgrade that can improve your home's curb appeal.

Bar soap or petroleum jelly is a common way to repair squeaky hinges. Rub the item onto the hinges until it's coated.

Replacement Hinges

If they're worn out or damaged, hinges can cause major damage. Hinges are easy to replace and do not require any special tools. It is crucial to select the right hinge for your home. This will ensure that your door closes and opens easily. If your door hinges aren't functioning properly, consult a professional to repair them as soon as possible.

A faulty hinge can cause the door to warp or pull away from the frame. Often, this is caused by improper use or excessive weight. To avoid this from happening, it is crucial to keep your hinges lubricated. This will prevent the hinge from rusting or squeaking, and will extend the lifespan of your doors.

There are a variety of hinges. Each type has its own advantages and drawbacks. The most common hinge is the butt joint which is secured to the door by putting pins on each side. This kind hinge is suitable for doors with light weights as it doesn't need much strength to open and shut. The butt joint is more susceptible to damage than other hinge.

For heavier doors, it's best to choose a continuous piano hinge. This type hinge is fixed to the door and extends the entire length of the door, allowing it to close and open with ease. The advantage of this kind of hinge is that it doesn't require a center support and is more sturdy than other hinges.

The storefront door pivot is another common type of hinge. It allows doors to pivot from one point at the top or bottom of the door. They are typically located in commercial areas and can be difficult to repair if damaged. Experts can assist you by installing an entirely new pivot or replacing the old one. Depending on the type of hinge you choose, the price will differ.

Loose Hinges

If hinges aren't in good condition they will cause the door to hang in a crooked manner and may even start scraping against the floor, which is irritating at best. In general, loose hinges are a problem that can be easily fixed by any homeowner who has just a few basic tools. In most cases, tightening the hinge screws can fix the issue however in some instances the screws may have become stripped and won't stay in place. If the screw holes are stripped, you will have to drill the holes and plug them in with wooden dowels or glue-coated wooden matches.

It is important to lubricate and tighten your door hinges on a regular basis to avoid them becoming loose. It is also essential to look for any signs of damage to the hinges. If you notice any chips or cracks in the material, this could be an indication that it's time to replace the hinge. It's also recommended to replace the hinges when you notice that they're beginning to become stuck or bind when you open and close the door.

The most frequent cause of door hinges becoming loose is wear and tear from constant use, without proper tightening or lubrication. This is especially relevant for doors that are frequented by children as they might hang from the handles of doors or swing the door around on the hinges. This could cause the hinges to become loose and even fall out.

If the hinges have been loose for a short period of time, you may just tighten them with the help of a screwdriver. However, should they be loose for a longer time the constant movement of the hinge plate as well as the screws will begin to enlarge the holes the screws enter. This will eventually make it impossible for the screws to stay in place and they will be ripped, rendering them ineffective. To fix this, dip the bare end of a match made of wood into regular carpenter's adhesive and then tap it a bit using a hammer to push the glue into the hole as far as you can. It is likely that you will require a few matches coated with glue to fill in the hole.

Rusty Hinges

Rust is a common problem for door hinges, especially on older doors. It can make them look poor, but most importantly, it can cause the hinge to fail and break and pose a risk to people who use the door. It is possible to save an old hinge with a bit of work. The first step is removing hinges and cleaning them to eliminate any gunk. After the hinges have been cleaned they can be oiled before being used again.

Modern doors are made of brass or metal alloys, which don't rust easily. However, some people still prefer old-fashioned iron hinges for their durability and beauty, even though they are more likely to rust than modern hinges. The best way to prevent this is to prevent the hinge from rusting in the first place.

It is simplest to clean the hinges regularly using steel wool and water, especially when they are damp. If you keep doing it often, rust won't be a problem with the hinges on your door.

If you're looking to go further, consider using stainless steel for your hinges. As opposed to iron, stainless steel will not rust and can provide your home with a more modern aesthetic. If you can't replace your existing hinges the best thing to do is periodically scrub them, and then lubricate them.

It is best to take the hinges off completely so you can scrub any rust that has accumulated. Once the hinges are cleaned, you can use a mix of oil and vinegar to provide lubrication and protect them from corrosion. This is a cost-effective and easy solution that you can find in the majority of homes. It's worth trying before replacing hinges.

Doors that won't shut





Sometimes doors may become misaligned as time passes because of the normal expansion and contraction of wood. If this occurs, the door could be caught on the corners of the frame or catch on the latch when you attempt to shut it. These issues can be solved by a bit of effort. If you can tighten the hinges and fix the alignment issue then your door will close correctly again.

Check the hinges to see whether there are loose screws. Loose screws can cause a hinge to sag and create an opening between the leaf of the hinge and the jamb. key cutting cambridge can cause the latch not to reach the strike plate's hole, and cause a jammed-up door.

To fix this, remove one of the hinge screws and slide a piece of cardboard (we prefer the backs of old legal pads) between the hinge and the door jamb. Fix the hinge. This will widen the gap along the hinge side and narrow it down on the latch side, allowing the latch to be free of the strike plate. If this resolves the issue, repeat the procedure on the remaining hinges.

If you tighten the hinges and use longer screws to fix the alignment of the holes in your strike plate does not solve the issue, you may need to shim or hammer the strike plate to ensure it is aligned with the latch hole. If this is the case, a little bit of paint and wood filler will usually do the trick to hide the changes.

Damage to the body and use for a long time can also cause the strike plate to become curled or twisted, which can cause the latch to touch the edge of the hole and not extend into it far enough to ensure that the door is closed. To check for this apply lipstick to the latch and then stick an ad-hoc strip of masking tape on the strike plate. Close the door, then open it. The lipstick should leave a mark on the tape where the latch touches the strike plate's hole. If the mark is below the hole then your latch needs to be moved up.