How to Install a Vinyl FenceA fence made of vinyl is an attractive low-maintenance method to define property lines and keep children and pets in a safe environment. However, it is essential to be aware of every detail when installing a fence made of vinyl.The first step is to stake out your intended fence line and determine how many posts you'll require. Generally, fence posts should be 6 to 8 feet apart.Dig PostholesDig postholes into your fence line using a powered digger or auger (check for local codes). The holes should be around 10 inches wide and deep enough to hold approximately 1/3 of the length of the pole plus 6 inches of gravel backfill. To improve strength, gate posts and main supports should be six inches deeper than the other posts.After digging the posts, pour around six inches of gravel into the holes, and then fill the posts with quick-setting concrete following the mixing and setting directions on the bag of concrete. The hollow post should be tapped into the concrete and check that each post is level and plumb before moving to the next.Consider installing drainage systems if your fence is placed over a source of water to keep water from accumulating in the holes. You can also put the gravel layer between the fence and the ground to help to prevent erosion of the soil.Contact the local utility diggers hotline before you start digging. They will mark underground lines. This will prevent any unexpected situations, like a leaking water or sewer line, while installing your fence.After you've marked your holes, dig each to a depth of 2.5' to 3'. To ensure that the rails of your post be inserted into the holes the bottom of the hole must be larger than the top of the post.Reduce the length of your posts.It is essential to ensure that the posts are the same length if you want to install vinyl fencing. This is important since it allows the fence to bend without breaking. pool fencing installation will ensure that the fence can withstand minor impacts and high winds.You can ensure you have the exact length of posts by using a level to measure them and marking them on strings. You can mark the strings on the top posts, or you can use them to line up each posthole.Once you have the posts marked make holes to the appropriate depth for the fence. The holes should be deep enough to hold 3 feet of post and 6 inches of gravel. This will provide the foundation for the post that will let water drain away.Next, insert the bottom rail into each post and fix it using a self drilling screw. This will stop the top rail from sliding off the post and will allow for in-and out movement.Once the bottom rail has been installed after that, move your pickets along the u channel until you have completed the entire section. Next, insert your top and middle rails.When you install privacy fences made of vinyl, make sure to insert the u channel before you attach the top rail to the post. This will prevent your fence's sagging from the wind, and will also keep out insects and other debris.Install PostsIt is crucial to follow the manufacturer's instructions when installing the vinyl fence. This includes digging holes deep enough to support at least a third of the post's length, and 6 inches deep in the case of a gravel base.If you're installing a fence made of vinyl on an inclined slope, it's important to make sure that the posts are level. A high post can cause the whole fence to sag and make it difficult to secure the panels.To ensure that your posts are set straight, use a string and tie it to the other corner or end of the post prior to the time you dig the hole for it. cost for vinyl fence installation will help you determine the exact position of your post.Ideally the posts should be at least one-third deeper than their length to give them more strength and stability. This can be done quickly and easily using the use of a post-hole drill or you can dig them manually.When you have the posts in place and you are ready to fill them with concrete. Fill the cement to a depth of approximately one foot and evenly distribute it evenly. This will make the posts stronger and more able to stand up to strong winds.Once the posts are set, attach rails. The rails attach to posts by snapping them into the slots at the top and bottom. Once the rails are secure then you can slide the vinyl fencing panels in place.Attach rails to postsPosts are the basis of your fence made of vinyl and should be strong enough to withstand the weight of the fence. Posts could tip or move if the ground is unstable. This could cause damage to your fence. Concrete at the base is the best method to ensure the stability of your posts.It isn't easy to connect a post to rails, but it is possible. You can make use of a tool called a "post brace" to keep the post plumb and straight. These are usually made of two-foot by four-foot boards that are connected to the post with nails or the claw hammer.Once the post is secured, place the rails on the top. If you are installing split rails you can slide the lower rail down until it is clear of one of the posts next to it. Continue to add the rails until all of the posts are set and the fence is finished.For pickets that are spaced, consult the local code enforcement department for specific spacing. If your fence is set on a sloped landscape it could be necessary to cut the pickets in a step pattern. This is not critical, but it does help hide the staggered board ends.It is important to choose the appropriate fence style for your property and landscaping. The fence should fit with the overall design of your property and provide security, privacy and curb appeal. A fence that is in the right design can help reduce maintenance and repair costs.Attach rails to postsVinyl fences are easy to install and are available in a wide range of styles. vinyl fencing install include privacy fences, split rail fences and picket fences. They are a popular alternative to wood fences because they are durable and low maintenance.Before you start digging holes to set the posts, measure the distance between the posts to ensure the fence is constructed in an even line. Then use a string to mark and place the posts.After the posts are ready to be erected, you must dig holes for each post leaving 5 to 6 inches of space above the ground. If you have a sloped property concrete can be added to the bottom of each post.Once the posts are put up, you can attach fence rails to the posts. Vinyl fence rails are available in lengths of 16 and 8 feet which means you can pick the one that is best suited to your home.You'll need to trim the rails in order to be able to fit around corners if the fence has corners. To slide the rail across the posts that are at the corners you can make use of one end of the rail and the opposite end to slide it through another post.Once you've connected the rails, you're able to begin to insert the fence pickets onto each rail. This will give your fence a professional look. This will allow you to visually grade your fence to ensure it looks consistent.Attach Posts to PostsVinyl fences are an excellent option for homeowners who want to improve their property's appearance, privacy, and shield their gardens from weather damage. They are durable and require only minimal maintenance.There are a variety of vinyl fences such as picket, solid privacy, and picket. Each style of fence comes in various sizes and colors, and some are even available with a lifetime warranty.Consider pool fencing installation manufacturing process of the vinyl fence manufacturer prior to selecting a fence for your home. There are two primary methods to make vinyl fencing: monoextrusion and co-extrusion.The first method injects polyvinyl chloride (PVC) with UV inhibitors to avoid chalking and fading. The latter method uses the double-layer of PVC to create a capstock and substrate.Vinyl fences are also infused with impact modifiers, stabilizers, and other substances that make them tough and flexible. They are also resistant to rot and decay and some even come with lifetime warranties.If you're not sure about the type of vinyl fence you should purchase contact your local dealer for advice. They can help you find the ideal fence for your needs and help you make a decision.After you've selected a vinyl fence to fit your home, it is time to begin the installation. This phase of the project could be a little challenging, so it's important to follow the directions carefully.