How to Install a Vinyl FenceVinyl fencing is a beautiful and low-maintenance means of defining property lines as well as keeping pets and children secure. But installing one yourself requires careful planning and care for the details.First, you'll need to determine the amount of posts needed and then stake out the fence line. Fence posts should be placed 6-8 feet apart.Dig PostholesUse a power auger, or digger, to create postholes in your fence. Be sure to check with your local codes. The holes should be about 10 inches in diameter . They should be deep enough to support about one-third of the length of the pole plus 6 inches of gravel backfill. To increase strength, gate posts and main supports must be six inches deeper than the other posts.After digging the posts, pour about six inches of gravel into the holes, and then fill them with concrete that sets quickly, following the mixing and setting guidelines on the concrete bag. Tap the hollow post into the concrete and make sure that each post is level and plumb before moving on to the next.If your fence is positioned near a water source, consider a drainage system to keep the water from accumulating in the post holes. To prevent erosion from water you could also add gravel between the fence & the ground.Before you begin digging, contact the local utility diggers hotline so that you can have your underground lines marked. This helps you avoid any surprises, like leaky water or sewer line, while installing your fence.After you've marked your holes, you'll need to dig each one to a depth of 2.5' to 3'. The bottom of the hole should be larger than the top of the post, so it will be able to fit in the post's rails when you put them in.Reduce the length of your posts.It is essential to ensure that the posts are the identical length if you intend to install vinyl fencing. This will allow the fence to bend but not break. This ensures that the fence is able to withstand minor impacts and high winds.You can ensure that you have the exact length of posts by using a level to measure them, and then marking them on strings. You can mark the strings at the posts' ends or use them to line up the postholes.Once you've marked the posts then dig holes to the proper depth for the fence. These should be deep enough to allow for 3 feet of post and 6 inches of gravel. This will give the post with a base that will drain water away.Then, you can insert the bottom rail into each post and secure it with an self-drilling screw. This will prevent the top rail from sliding off the post and will allow for the movement of in-and-out.Once the bottom rail is in then slide your pickets in and U-channels as needed until you've completed the entire section. Then, insert your top and middle rails.If you're installing a privacy fence, place the u channel before you hammer the top rail into the post. This will keep your fence from sliding in the wind and will help to keep out bugs and debris.Install PostsIt is important to follow the instructions of the manufacturer when installing the vinyl fence. This includes digging holes that are sufficient in depth to hold at least 1/3 of the posts length and six inches deeper in the case of a gravel base.If you're installing a vinyl fence on a slope, it's especially important to ensure that the posts are level. This is because a post that is too high could cause the entire fence to tilt and make it difficult to secure the fence properly.To ensure that your posts are straight using a string, connect it to the corner or end of the post prior to the time you dig the hole. This will help you find the exact position of your post.To give them greater strength and stability, the posts should be at least a third larger than their length. This is done quickly and easily with the use of a post-hole drill or you can dig them manually.Once the posts are placed and the concrete is poured over them, you can pour it on. The cement should be about 1 foot deep, and evenly distributed. This will make the posts more sturdy and help them withstand strong winds.Once the posts are in place After that, you can attach the rails. The rails snap into slots at the top and bottom of the posts. After the rails are secured, you can slide your vinyl fencing panels in place.Attach rails to postsPosts are the basis of your vinyl fence and should be strong enough to withstand the weight of the fence. Posts can tip or move when the ground is unstable. This could cause damage to your fence. The best method to ensure the strength of your posts is to put concrete for the base.It can be difficult to attach a post rails, but it is possible. To ensure that your post stays straight and level it is possible to use a "post brace". The boards are typically 2 feet by 4-foot and can be attached to the post using nails or using a clawhammer.After the post has been secured after which you can place the rails on the top. Split rails can be put in by sliding the rail on the bottom down until it clears one of its posts. Continue adding rails until all posts are installed and the fence is completed.For pickets that have spaced spaces, check with your local code enforcement office for specific spacing. If your fence is in a sloped location it may be necessary to cut the pickets into an angled pattern. This isn't a necessity however it can be helpful to conceal the staggered ends of the fence.It is crucial to pick the right fence style for your home and landscaping. The fence should match the overall appearance of your home and offer privacy, security, and curb appeal. A fence that is in the right design can reduce maintenance and replacement costs.Attach rails to postsVinyl fences are simple to set up and are available in a variety styles. They include privacy fences as a well as split rail and picket fences. gates installers near me are long-lasting and require minimal maintenance, making them a popular choice to wooden fences.Before digging holes for the posts the distance between the posts to ensure that the fence is constructed in straight lines. Use a string to mark and set all of the posts.When the posts are ready make holes for each post, leaving 5 to 6 inches of space above the ground. You may also apply concrete to the post's base if you have a sloped yard.After all posts are set Once the posts are in place, you can connect the fence rails to them. The vinyl fence rails come in lengths of 16 and 8 feet, so you can choose the appropriate size for your property.You'll have to trim the rails to fit around corners , if the fence has corners. You can use the end of one rail to slide it over the corner post and then the opposite end of the rail to slide it into the next post.After you've hung the rails, you're able to start putting the fence pickets onto each rail. This will give your fence a professional appearance. It also gives you the opportunity to visually grade your fence so that it appears consistent from an extended distance.Attach Posts to Other PostsVinyl fences are a desirable alternative for homeowners who wish to enhance the curb appeal of their property and privacy while also protecting their gardens from weather damage. They are durable and require minimal maintenance.There are many types of vinyl fences that include picket, solid privacy, and picket. Each type of fence is available in many sizes and colors, and some are even offered with a lifetime guarantee.Consider the manufacturing process of the vinyl fence manufacturer prior to choosing a fence for your property. There are two main methods of making vinyl fencing: monoextrusion and co-extrusion.The first method injects polyvinyl chloride (PVC) with UV inhibitors to avoid chalking and fade. To create a capstock as well as a substrate the second method utilizes the double layer of PVC.Vinyl fences are also infused with impact modifiers, stabilizers and other materials that make them strong and flexible. They are also resistant to decay and rot and some even come with lifetime warranties.If you're unsure about the kind of vinyl fence to buy, ask your local dealer for suggestions. They'll be able to help you navigate in the right direction and suggest the best option to meet your needs.Once you have chosen the right vinyl fence for your home, it's time to start the installation. This part of the job can be a bit challenging, so make sure you follow the steps.